Honda Archives

2007 Honda CR-V
Mileage
126,058
Service Date
6/6/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
STANDARD SYNTHETIC BLEND OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic blend motor oil per manufacturer specifications, additional quarts, grades, or full synthetic oils extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT DRIVE BELTS AND HOSES –INSPECT FRONT/REAR WIPER BLADES –INSPECT THE TIRES AND SET TO PROPER PSI ** –INSPECT THE ENGINE AIR FILTER AND CABIN AIR FILTER –INSPECT FRONT AND REAR SUSPENSION –INSPECT FRONT/REAR STRUTS/SHOCKS –PERFORM EXTERIOR VEHICLE LIGHT INSPECTION –INSPECT CV AXLES/BOOTS/DRIVESHAFT(S) –INSPECT STEERING LINKAGE –RESET SERVICE LIGHT –ROAD TEST VEHICLE –CLEAN WINDSHIELD *** ** TIRE ROTATION ADDITIONAL FEE *** WASH VEHICLE WHEN TIME PERMITS
California Recycling Fee
Environmental Waste Disposal Fee, EPA ID# CAL000295851
FOUND:
Install premium grade brake pad set, clean and lubricate the caliper guides and hardware, inspect the hydraulic system reassemble and make adjustments as required. Remove brake rotors for resurfacing or replacement.
Replace the battery as required, reassemble with equipped hold-down hardware.
CALIFORNIA LEAD ACID BATTERY FEE
Inspect the tire PSI and Inflate to Proper Specifications Front __30___PSI Rear__30___PSI
MARY & JOHN F. gave our service a 5 star review on 6/8/2024
2017 Honda Civic
Mileage
80,772
Service Date
5/28/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
STANDARD SYNTHETIC OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic motor oil per manufacturer specifications, additional quarts, grades, extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT DRIVE BELTS AND HOSES –INSPECT FRONT/REAR WIPER BLADES –INSPECT THE TIRES AND SET TO PROPER PSI ** –INSPECT THE ENGINE AIR FILTER AND CABIN AIR FILTER –INSPECT FRONT AND REAR SUSPENSION –INSPECT FRONT/REAR STRUTS/SHOCKS –PERFORM EXTERIOR VEHICLE LIGHT INSPECTION –INSPECT CV AXLES/BOOTS/DRIVESHAFT(S) –INSPECT STEERING LINKAGE –RESET SERVICE LIGHT –ROAD TEST VEHICLE –CLEAN WINDSHIELD *** ** TIRE ROTATION ADDITIONAL FEE *** WASH VEHICLE WHEN TIME PERMITS
California Recycling Fee
Environmental Waste Disposal Fee, EPA ID# CAL000295851
FOUND:
Inspect the tire PSI and Inflate to Proper Specifications Front __33___PSI Rear__33___PSI
PERFORM NECESSARY DIAGNOSTIC TESTING AND ADVISE:
FOUND: I inspected the vehicle and verified the client's concern that the check engine light is illuminated. I found there is an extended crank symptom present and a significant lack of power above 3,800 rpm. I retrieved diagnostic trouble code P0340 which indicates there is no signal present from the intake camshaft position sensor. I performed necessary diagnostic testing and found there is substantial damage to the powertrain wiring harness due to varmints. Recommend partially removing the wiring harness in order to facilitate repair, perform repairs, reinstall the vehicle harness, clear the codes and test drive to verify there are no additional faults.
I inspected the door lock operation and verified the clients concern that the doors do not lock. I verified the fault is present during key fob use and power door lock button operation. I found there are no trouble codes stored in the body control module. During testing I found there is a door jar signal present at the body control module which is prohibiting the door locks from locking. I continued the inspection on the door lock system wiring and found there is damage to the body control module harness from varmints. Recommend partially removing the body control module harness, performing necessary repairs, reinstalling and reinitializing the power door lock system.
DISASSEMBLE, REPAIR THE ELECTRICAL WIRING AS REQUIRED, REASSEMBLE, TEST FOR PROPER OPERATION.
REPLACE THE FRONT AND REAR WINDSHIELD WIPER BLADES
Rotate the tires and re-balance them. Enjoy a smoother ride while extending tire life!
Inspect and make required adjustments to set "toe", "caster", and "camber" to factory specifications on the front and rear suspension (where applicable). Alignment warranty requires tire rotations and checking tire pressure in accordance with manufacturer's specifications.
REPLACE THE CABIN AIR FILTER
EXTRACT BROKEN BOLT FROM AIR FILTER HOUSING
PHILIPPE M. gave our service a 5 star review on 5/28/2024
2014 Honda CR-V
Mileage
120,191
Service Date
5/24/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
******************************************************************************************
STANDARD SYNTHETIC OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic motor oil per manufacturer specifications, additional quarts, grades, extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT DRIVE BELTS AND HOSES –INSPECT FRONT/REAR WIPER BLADES –INSPECT THE TIRES AND SET TO PROPER PSI ** –INSPECT THE ENGINE AIR FILTER AND CABIN AIR FILTER –INSPECT FRONT AND REAR SUSPENSION –INSPECT FRONT/REAR STRUTS/SHOCKS –PERFORM EXTERIOR VEHICLE LIGHT INSPECTION –INSPECT CV AXLES/BOOTS/DRIVESHAFT(S) –INSPECT STEERING LINKAGE –RESET SERVICE LIGHT –ROAD TEST VEHICLE –CLEAN WINDSHIELD *** ** TIRE ROTATION ADDITIONAL FEE *** WASH VEHICLE WHEN TIME PERMITS
California Recycling Fee
Environmental Waste Disposal Fee, EPA ID# CAL000295851
Inspect the tire PSI and Inflate to Proper Specifications Front __33___PSI Rear__33___PSI
DISASSEMBLE, REPLACE THE ENGINE OIL PAN GASKET, REASSEMBLE, CLEAN AS BEST POSSIBLE.
Rotate the tires front to rear to extend tire life.
FOUND:
REPLACE THE ENGINE AIR FILTER
INSPECT AND ADVISE: I inspected the vehicle and verified the client's concern that there is a rattle noise present upon cold startup. I isolated the noise to the timing chain components. I suspect the intake variable valve timing phaser has failed and no longer locks in the retarded position for engine startup. Recommend removing the valve cover, confirming the phaser has failed, performing necessary repairs and verifying there are no additional faults.
* UPON DISASSEMBLY, WE FOUND THAT THE TIMING CHAIN IS STRETCHED TO THE MAXIMUM LIMIT AND WILL REQUIRE REPLACEMENT.
Inspect and make required adjustments to set "toe", "caster", and "camber" to factory specifications on the front and rear suspension (where applicable). Alignment warranty requires tire rotations and checking tire pressure in accordance with manufacturer's specifications.
Clean the throttle body and butterfly valve, clean the mass air flow sensor, induce a cleaner to service the intake valves, intake plenum, combustion chamber, piston tops, + add a concentrated cleaner to the fuel tank. Take advantage of these cleaning chemicals by filling your fuel tank right away!
DEBORAH B. gave our service a 5 star review on 5/24/2024
2014 Honda Accord
Mileage
106,558
Service Date
5/9/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
REMOVE & REPLACE- INTAKE HOSE
MATT & DONNA S. gave our service a 5 star review on 5/9/2024
2020 Honda Odyssey
Mileage
48,644
Service Date
4/19/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
Wash and wax the exterior, clean the wheels and wheel wells, vacuum and clean the carpets, seats, trunk and door panels, clean windows, and apply dressing to the tires, vinyl, and plastic.
RONDA A. gave our service a 5 star review on 4/19/2024
2010 Honda Insight
Mileage
156,156
Service Date
4/17/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
REFERRED BY EVANS TIRE
THE CUSTOMER STATES THE VENTS ONLY BLOW ON THE DEFROST MODE. INSPECT AND ADVISE ON NEEDED REPAIR.
FOUND: I inspected the vehicle and verified the client's concern that the HVAC system does not direct air as anticipated. I inspected the mode door operation and found the mode door motor fails to properly operate. Code b1239 is present in HVAC module and indicates there's a short with the mode control motor circuit. I inspected the exposed portions of the wiring and found no indication of a fault. Replacement of the mode door motor will be required. Recommend replacing the mode door actuator, clearing the code and reevaluating the system for additional potential faults. I inspected the HVAC system and confirmed the client's concern that the outlet temperature is warmer than anticipated when set to the max cold setting. I recovered the refrigerant from the system and found the refrigerant level is low. I recharged the system with the proper amount of refrigerant and continued the inspection. I found the HVAC compressor fails to engage. I checked the circuit for power and found there is no power available at the compressor. I checked the fuse for the compressor and found the fuse is good. Diagnostic testing will be required on the HVAC compressor circuit. Recommend performing electrical testing on the HVAC compressor circuit.
Visual inspections of the system, test pressures, inspect compressor, belt and clutch operation, add refrigerant and retest Post service center outlet temperature: 47°F Post service high side pressure: 190 Post service low side pressure: 30
REMOVE & REPLACE- MODE DOOR ACTUATOR
FOUND:
CONTROL ARM – Remove & Replace – Lower,Both – [DOES NOT include alignment.]
REMOVE & REPLACE- AIR FILTER
REMOVE & REPLACE- CABIN FILTER
TIE ROD &/OR END – Remove & Replace – Outer,Both – [Includes: Adjust toe-in only. NOTE: Deduct .4 if alignment is also performed. NOTE: Manufacturer recommends removal of Rack and Pinion Steering Gear when replacing Inner Tie Rod End(s) on some models. If
Inspect and make required adjustments to set "toe", "caster", and "camber" to factory specifications on the front and rear suspension (where applicable). Alignment warranty requires tire rotations and checking tire pressure in accordance with manufacturer's specifications.
STABILIZER BAR CONTROL LINK – Remove & Replace – Both
Replace the battery as required, reassemble with equipped hold-down hardware.
CALIFORNIA LEAD ACID BATTERY FEE
Rotate the tires and re-balance them. Enjoy a smoother ride while extending tire life!
SHOCK ABSORBER – Remove & Replace – Both
USE THE FACTORY RECOMMENDED OIL TYPE AND QUANTITY.
Environmental Waste Disposal Fee, EPA ID# CAL000295851
Extract the existing brake fluid, replenish the system with fresh fluid, bleed the system of any air or preexisting brake fluid.
Clean the throttle body and butterfly valve, clean the mass air flow sensor, induce a cleaner to service the intake valves, intake plenum, combustion chamber, piston tops, + add a concentrated cleaner to the fuel tank. Take advantage of these cleaning chemicals by filling your fuel tank right away!
Pressure test the system, inspect the accessory drive belts and cooling system hoses, drain and refill the cooling system.
ENGINE OR TRANSMISSION MOUNT – Remove & Replace – Engine,Side
REMOVE & REPLACE- WIPER BLADES
STANDARD SYNTHETIC OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic motor oil per manufacturer specifications, additional quarts, grades, extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT
BRETT M. gave our service a 5 star review on 4/17/2024
2020 Honda Accord
Mileage
16,675
Service Date
4/17/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
STANDARD SYNTHETIC OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic motor oil per manufacturer specifications, additional quarts, grades, extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT DRIVE BELTS AND HOSES –INSPECT FRONT/REAR WIPER BLADES –INSPECT THE TIRES AND SET TO PROPER PSI ** –INSPECT THE ENGINE AIR FILTER AND CABIN AIR FILTER –INSPECT FRONT AND REAR SUSPENSION –INSPECT FRONT/REAR STRUTS/SHOCKS –PERFORM EXTERIOR VEHICLE LIGHT INSPECTION –INSPECT CV AXLES/BOOTS/DRIVESHAFT(S) –INSPECT STEERING LINKAGE –RESET SERVICE LIGHT –ROAD TEST VEHICLE –CLEAN WINDSHIELD *** ** TIRE ROTATION ADDITIONAL FEE *** WASH VEHICLE WHEN TIME PERMITS
California Recycling Fee
Environmental Waste Disposal Fee, EPA ID# CAL000295851
FOUND:
Inspect the tire PSI and Inflate to Proper Specifications Front __32___PSI Rear__32___PSI
REPLACE THE ENGINE AND CABIN AIR FILTERS
LAURIE L. gave our service a 5 star review on 4/17/2024
2014 Honda Pilot
Mileage
178,105
Service Date
3/29/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
PERFORM NECESSARY DIAGNOSTIC TESTING AND ADVISE:
FOUND: I inspected the vehicle and verified the client's concern that the check engine light is illuminated and flashing, and there is a significant drivability issue present. I retrieved diagnostic trouble code p0355 which indicates there's a primary circuit fault with the number 5 ignition coil. I performed necessary diagnostic testing and found the wiring to the ignition coil has been damaged due to varmint infestation. I repaired the wiring, cleared the code and test drove the vehicle. I found there are no additional misfires present. Monitor the condition and advise.
DISASSEMBLE, REPAIR THE ELECTRICAL WIRING AS REQUIRED, REASSEMBLE, TEST FOR PROPER OPERATION.
SHIREEN Y. gave our service a 5 star review on 3/29/2024
2009 Honda Fit
Mileage
10,662
Service Date
3/26/2024
Services Performed
AAA DISCOUNT REWARDS MEMBER CARD # ……………………………
OIL CHANGE/ CHECK PASSENGER SIDE WINDOW. THE FUSE WAS REMOVED AS IT WAS VERY SLOW TO ROLL UP.
FOUND: WE FOUND THE PASSENGER SIDE WINDOW REGULATOR WORKING WHEN FORCING POWER TO THE REGULATOR. AT THIS TIME WE RECOMMEND TO START WITH A NEW MASTER SWITCH AND RECHECK THE SYSTEM OPERATION.
STANDARD SYNTHETIC BLEND OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic blend motor oil per manufacturer specifications, additional quarts, grades, or full synthetic oils extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT DRIVE BELTS AND HOSES –INSPECT FRONT/REAR WIPER BLADES –INSPECT THE TIRES AND SET TO PROPER PSI ** –INSPECT THE ENGINE AIR FILTER AND CABIN AIR FILTER –INSPECT FRONT AND REAR SUSPENSION –INSPECT FRONT/REAR STRUTS/SHOCKS –PERFORM EXTERIOR VEHICLE LIGHT INSPECTION –INSPECT CV AXLES/BOOTS/DRIVESHAFT(S) –INSPECT STEERING LINKAGE –RESET SERVICE LIGHT –ROAD TEST VEHICLE –CLEAN WINDSHIELD *** ** TIRE ROTATION ADDITIONAL FEE *** WASH VEHICLE WHEN TIME PERMITS
Environmental Waste Disposal Fee, EPA ID# CAL000295851
California Recycling Fee
FOUND: WE FOUND THE FRONT & REAR BRAKE LININGS IN SPECIFICATIONS AT THIS TIME.
DOOR WINDOW SWITCH – Remove & Replace
TIE ROD &/OR END – Remove & Replace – Outer,Both – [Includes: Adjust toe-in only. NOTE: Deduct .4 if alignment is also performed. NOTE: Manufacturer recommends removal of Rack and Pinion Steering Gear when replacing Inner Tie Rod End(s) on some models. If
Inspect and make required adjustments to set "toe", "caster", and "camber" to factory specifications on the front and rear suspension (where applicable). Alignment warranty requires tire rotations and checking tire pressure in accordance with manufacturer's specifications.
Extract the existing brake fluid, replenish the system with fresh fluid, bleed the system of any air or preexisting brake fluid.
Replace the battery as required, reassemble with equipped hold-down hardware.
CALIFORNIA LEAD ACID BATTERY FEE
Inspect the tire PSI and Inflate to Proper Specifications Front __32___PSI Rear__32___PSI
VIKKI & LLOYD R. gave our service a 5 star review on 3/27/2024
2017 Honda CR-V
Mileage
28,448
Service Date
3/14/2024
Services Performed
STANDARD SYNTHETIC OIL CHANGE SERVICE: ____ SERVICE LIGHT RESET (This price applies to most cars, SUV's, trucks, and European cars cost extra) ____ LUBE STICKER Quote is for 5 quarts of Multi-grade synthetic motor oil per manufacturer specifications, additional quarts, grades, extra –OIL AND FILTER CHANGE – Replace the oil drain plug sealing washer where applicable –FULL DIGITAL VEHICLE INSPECTION W/PICTURES –CHECK AND TOP OFF ALL FLUIDS –VISUAL BRAKE INSPECTION FRONT AND REAR –VISUAL CHECK FOR POSSIBLE OIL LEAKS –INSPECT DRIVE BELTS AND HOSES –INSPECT FRONT/REAR WIPER BLADES –INSPECT THE TIRES AND SET TO PROPER PSI ** –INSPECT THE ENGINE AIR FILTER AND CABIN AIR FILTER –INSPECT FRONT AND REAR SUSPENSION –INSPECT FRONT/REAR STRUTS/SHOCKS –PERFORM EXTERIOR VEHICLE LIGHT INSPECTION –INSPECT CV AXLES/BOOTS/DRIVESHAFT(S) –INSPECT STEERING LINKAGE –RESET SERVICE LIGHT –ROAD TEST VEHICLE –CLEAN WINDSHIELD *** ** TIRE ROTATION ADDITIONAL FEE *** WASH VEHICLE WHEN TIME PERMITS
California Recycling Fee
Environmental Waste Disposal Fee, EPA ID# CAL000295851
Inspect the tire PSI and Inflate to Proper Specifications Front __32___PSI Rear___32__PSI
Rotate the tires and re-balance them. Enjoy a smoother ride while extending tire life!
FOUND:
Extract the existing brake fluid, replenish the system with fresh fluid, bleed the system of any air or preexisting brake fluid.
Inspect and make required adjustments to set "toe", "caster", and "camber" to factory specifications on the front and rear suspension (where applicable). Alignment warranty requires tire rotations and checking tire pressure in accordance with manufacturer's specifications.
DAVID D. gave our service a 5 star review on 3/15/2024